CHE 333 Class 20

CHE 333 Class 19 Fracture continued Dynamic Fatigue Fatigue is failure due to a stress being repeatedly applied to a metal. After a number of cycles the component fails. Examples include aircraft, axles, and shafts. Stresses 1. Cyclic tension compression fully reversed

tension zero tension tension non zero tension sine wave, saw tooth, trapezoidal with delay. 2. Stress Rato R= smax/smin

Stress V Log Nf Curves Ferrous, that is BCC iron based have a knee in the stress, number of cycles to failure Data, while non-ferrous does not. Safety ranges can be determined for ferrous, while the Stress range for 107 cycles is used for non-ferrous metals. Micro Process Stage I slip lines intersect with surface of material at 45o to stress axis. Form Persistent Slip Band Crack initiates in slip band and grows at 45o to stress single slip system. 25 -50 % Nf

Stage II At crack tip, as tensile stress increases, multiples slip systems, crack grows along them both producing Striations, identifying fatigue., 74 49% Nf Stage III Crack length such that it is approached K1c value, so overload failure as stress increases. Fatigue Fracture Surface . Shaft broken by fatigue. Initiation site is at the top. Note the change in appearance when going from stage II to stage III.

Tube fractured by fatigue. Note river lines running from initiation sites on surface as well as multiple stage I intiation sites on surface. River lines connect cracks. Stage II Crack Growth Striations Coarse striations on surface

Fine striations on surface. River line indicates F crack growth direction while striations indicate i crack front. n Mixed Mode Crack Growth

Transition where some striations and some overload failure. Anisotropic effect? Striations indicate fatigue process lead to failure Fatigue Crack Growth Testing Cyclic stress on a pre cracked sample and measure crack length a as a function of number of cycles to produce a da/dN curve. Know a so can calculate DK, also from da/dN curve, for given value of N slope of curve is da/dN, growth rate per cycle. DK= YDs (pa)0.5

Crack Growth Rate Data log (da/dn) with corrosion Stage 11 Crack Propagation Region DKth

log DK Typical crack growth curve shown with three regions. The first is a threshold region which indicates a safe crack size below which no crack growth occurs. Then a steady state region of crack growth, and the third stage of rapid failure when plane strain fracture toughness is met. Lifing of components can be done using stage II. If the crack length and service stress is known, DK can be calculated and the crack growth rate obtained from graphs. The number of cycles before the crack length becomes critical can be determined and so the remaining life of the cracked component can be estimated

Factors Affecting Fatigue. Microstructure plate structure of Ti-6Al-4V better fatigue life than particle structure. Compressive stresses in the surface stop cracks opening shot peen Surface roughness rougher surface initiates cracks easier than smooth surface. Corrosion decreases fatigue life by initiating cracks easily so modifying stage I. Cyclic frequency increase frequency decreases fatigue life. Cyclic waveform trapezoidal detrimental for some titanium alloys Examination ultrasonic inspection, penetration X ray, die penetrant,

Creep Mechanisms Creep in metals is extension to failure under combined stress and temperature. The temperature is usually above 0.4 the melting point in oKelvin. The process occurring during creep involves grain boundaries at 45o to the stress axis sliding relative to each other. Diffusion of atoms is involved. s Grain Boundary slides due to atoms moving. Voids open

up and failure occurs grain boundary controlled Creep Creep can be split into three sections primary, decreasing creep rate, secondary with a steady state creep rate and tertiary creep with an increasing creep rate. Factors affecting creep are grain size, temperature, Small grain size detrimental for creep single crystal turbine blades used these days. Dont want blades elongating as they would rub against containment. Other area

include nuclear reactors. Creep Polymers Creep in polymers is measured by applying a load and measuring the extension after a set period of time. The creep modulus is then the stress divided by the strain. The higher the creep modulus the better. Note the low temperatures compared to metals.

Recently Viewed Presentations

  • Frog Dissection: Lab Practical Practice DSS: -Get a

    Frog Dissection: Lab Practical Practice DSS: -Get a

    Frog Dissection: Lab Practical Practice DSS: Get a ½ sheet of paper from the front Get a clicker from the bin in the front Take out your packet and REVIEW If you havent turned your packet in yet, I will...
  • The Research Life Cycle Rachel Curwen, Research Policy

    The Research Life Cycle Rachel Curwen, Research Policy

    The Research Life-Cycle. Ideas. Planning. Action. Dissemination. Application. Environment. Very important to note that while, understandably perhaps, lots of the support and process that happens at the Uni for research is about the financial side, this schema could apply to...
  • An Evaluation of the Technical Approaches to the

    An Evaluation of the Technical Approaches to the

    Overview. This research attempts to characterize the insider by drawing on prominent theories from the fields of behavioral theory and psychology to create an insider personality profile.
  • Outreach and Foster Healing - NJAMHA

    Outreach and Foster Healing - NJAMHA

    Sensory Motor Arousal Regulation Treatment (SMART) A comprehensive treatment approach that is organized to support arousal regulation in traumatized children by integrating: ... 75% of Foster Healing clients saw decreases in several trauma symptoms. Most of the clients had a...
  • All Hands Meeting: Education & Outreach and Diversity

    All Hands Meeting: Education & Outreach and Diversity

    After-School experience Peter Seidl Mentoring experience by Mike Johnson Part II: Diversity Introduction of guest speaker by Steve Gourlay Diversity Awareness by invited speaker Mary L. Topliff Part III (if time permits): Questions to GS Directors
  • Political Science Department

    Political Science Department

    Social sciences and the humanities. ... JMU offers Pre-law as a pre-professional program; students select major from a wide range of fields . THE JUSTICE STUDIES MAJOR. Core Requirements: Intro to Justice Studies . Foundation courses . Two in Track,...
  • La prima guerra civile: Mario e Silla - letteraturaestoria

    La prima guerra civile: Mario e Silla - letteraturaestoria

    La prima guerra civile (88-81 a.C.) Optimates e populares La Guerra Giugurtina Gaio Mario, homo novus riforma esercito La legione coortale I Cimbri e i Teutoni politica di Mario La guerra sociale (90-88 a.C.) guerra Mitridatica e inizio I guerra...
  • SOON-TO-BE Mountwest Community & Technical college

    SOON-TO-BE Mountwest Community & Technical college

    --offer opportunity to exit early (borderline students "refreshed" and can move on) Result: Early Exit possible/finish as early as 8th week /could sign up for 2nd 8week 100 . level content course . New . Issue: no lab space for...